aluminum electrolytic capacitors plastic platform voltage capacitance voltage mark for 6.3v is 6v . lot no. u 1 z 2 p 3 1 4 c 5 1 6 0 7 0 8 m 9 c 10 l 11 1 12 g 13 b 14 configuration taping code capacitance tolerance ( 20%) rated capacitance (10 f) rated voltage (16v) series name type x2 10 16v 0.3 max. 4.5 +0.1 0.2 d 0.5 b 0.2 c 0.2 0.5 max. a 0.2 a 0.2 e 0.5 ~ 0.8 zp series 4.5mml chip type, bi-polarized chip type with 4.5mm height. designed for surface mounting on high density pc board. applicable to automatic mounting machine using carrier tape. adapted to the rohs directive (2002/95/ec). chip type type numbering system (example : 16v 10 f) specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tan stability at low temperature endurance shelf life marking performance characteristics item 40 ~ +85? 6.3 ~ 50v 0.1 ~ 47 f 20% at 120hz, 20? after 2 minutes' application of rated voltage , leakage current is not more than 0.05 cv or 10 ( a) , whichever is greater. black print on the case top. measurement frequency : 120hz , temperature : 20? measurement frequency : 120hz after 2000 hours' application of rated voltage at 85? with the polarity inverted every 250 hours, capacitors meet the characteristic requirements listed at right. after storing the capacitors under no load at 85? for 1000 hours, and after performing voltage treatment based on jis c 5101-4 clause 4.1 at 20?, they will meet the specified value for endurance characteristics listed above. resistance to soldering heat the capacitors shall be kept on the hot plate maintained at 250? for 30 seconds. after removing from the hot plate and restored at room temperature,they meet the characteristic requirements listed at right. zp z 25? / z+20? z 40? / z+20? rated voltage (v) impedance ratio zt / z20 (max.) 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 dimensions 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 0r1 r22 r33 r47 010 2r2 3r3 4r7 100 220 330 470 5 6.3 6.3 28 37 45 6.3 0j 10 1a 16 1c 25 1e 35 1v 50 1h v code 4 6.3 6.3 17 33 41 4 5 6.3 6.3 12 23 37 49 5 5 6.3 12 16 27 4 5 5 6.3 8.4 16 18 29 4 4 4 4 4 5 5 6.3 1.0 2.0 2.8 4.0 8.4 13 17 20 rated ripple (marms) at 85? 120hz d a b c e 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 6.3 2.4 6.6 6.6 2.2 (mm) cap. ( f) rated voltage (v) tan (max.) 6.3 0.30 10 0.24 16 0.20 25 0.18 35 0.16 50 0.16 capacitance change leakage current tan within 10% of initial value initial specified value or less initial specified value or less capacitance change leakage current tan within 20% of initial value 300% or less of initial specified value initial specified value or less rated ripple frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz~ 0.70 1.00 1.17 1.36 1.50 taping specifications are given in page 24. recommended land size, soldering by reflow are given in page 25, 26. please select wp(p.47), un(p.77) series if high c/v products are reqired. please refer to page 3 for the minimum order quantity. case size d (mm) ze smaller wp smaller cat.8100v
|
